Commercial Gas Engineers in Leeds for Warehouses, Plant Rooms and New Supplies

Gas Engineers for the Sheds Along the M62 and M1

The distribution sheds at Logic Leeds by junction 45 of the M1, Leeds Valley Park, Stourton and the Wakefield Europort side of the M62 are heated by warm air and radiant heaters. When a heater fails or a supply is lost, the call is usually urgent.

Commercial Gas Engineer Near Me works on commercial and industrial gas only. Our engineers are Gas Safe registered and CSCS carded, the company is SSIP assessed, and we work seven days a week with a 24 hour emergency service.

We repair and replace high level heaters, run new supplies for packing lines and canteens, and test and purge pipework after every alteration. See commercial heating systems.

Why Does a Heater Repair Start With a Tightness Test?

Before an engineer replaces a gas valve, burner or ignition controller on a warm air heater, the supply to it has to be proved sound. A tightness test on the section shows whether the fault is in the appliance or in the pipework feeding it.

After the repair the section is tested again, purged if it has been opened, and the heater is relit and checked at its working pressure. You receive a record of the test and the work done. See gas testing and gas purging.

The same rule applies to boilers, water heaters and catering equipment.

Plant Rooms in Leeds Student Blocks and Offices Off the Headrow

Kirkstall Road, Burley, the Arena Quarter and the streets behind the universities have filled with student accommodation over the past decade. Each block has a plant room with boilers, water heaters and a gas supply that must be tested, purged and commissioned before the first residents arrive in September.

The office buildings around the Headrow, Park Square and Wellington Street have the same needs on a different timetable: boiler replacements in summer, tightness tests when a floor changes tenant, and a gas safety record every year for the building owner.

We install and alter the pipework, carry out the gas testing, commission the plant and issue the certificates. See commercial gas installation and commercial gas certificates.

New Supplies for Units in Millshaw, Gelderd Road and Sherburn

Industrial estates such as Millshaw and Gelderd Road in Beeston, Cross Green, Seacroft and Sherburn Enterprise Park in LS25 keep adding and reworking units. A new occupier often needs a larger supply than the last one, or a supply to a building that never had gas.

We lay underground gas pipework in polyethylene from the meter to the building, bring it above ground in steel, and connect it to the internal distribution. The buried run is tested before it is backfilled, and the whole system is tightness tested and purged before commissioning.

Where a whole unit is being cleared, we decommission the old system: isolate, purge to a safe outdoor point, cap, label and record, so nothing live is left behind a wall.

Can a Branch Be Added to a Live Main at a Yeadon Works?

Engineering firms around Yeadon, Guiseley and Rawdon, and food producers in Hunslet and Morley, cannot always stop for a connection. Hot tapping lets us fit a new branch to a live gas main: a fitting and valve are attached to the pipe, a drill cuts through under pressure, and the new outlet is connected and tested while the rest of the site keeps running.

It is a planned job with a survey and a written method statement, and it avoids a costly shutdown.

See our full range of commercial gas services, including commercial gas installation and gas testing & gas purging, or nearby areas such as Bradford and Sheffield.

Catering Gas From Chapel Allerton to the Corn Exchange

Restaurants in Chapel Allerton and Roundhay, the bars and food halls around the Corn Exchange and Kirkgate, hotel kitchens near the station and the stadium at Elland Road all cook on gas. We install commercial catering pipework, connect appliances, fit the gas and extraction interlock and carry out the annual inspection that a landlord or environmental health officer will ask for.

A kitchen that changes hands usually needs its supply resized for the new equipment. We test, purge and certify before opening night.

Northern Gas Networks, Leeds City Council and Street Works

Northern Gas Networks owns the gas distribution network across Leeds and the rest of Yorkshire, up to the emergency control valve at your meter. New connections, larger meters and disconnections are arranged with the network or through your gas supplier. From the meter outlet onwards the installation belongs to the site, and that is where we work.

Leeds City Council is the highway authority for the city's roads and footways, and any excavation in the public highway needs its permission. Bradford, Wakefield, Kirklees and Calderdale councils cover their own districts. We keep buried pipe routes on private land wherever possible.

Where Else in Yorkshire Do We Send Engineers?

We cover LS1 to LS29, from the centre of Leeds out to Otley, Ilkley, Wetherby, Garforth, Rothwell and Morley. Across the county we work in Bradford, Wakefield, Castleford, Pontefract, Halifax, Huddersfield, Harrogate, Skipton and York, so the BD, WF, HX, HD, HG and YO postcodes are all regular ground.

Engineers are based across the region rather than at a single depot, so the nearest available engineer is often close to your site. We also take on larger projects anywhere in the UK.

What Should a Facilities Manager Have Ready Before We Arrive?

• The location of the meter and emergency control valve, and who holds the keys.
• Any drawings or previous test and commissioning records for the installation.
• A list of the appliances on the section, and when they can be switched off.
• Site rules, permits to work and any induction the engineer needs to complete.

None of this is essential. If records are missing, we survey the system and produce a line diagram.